WV Crafter 2

manuals

car

Power

The ambulance contains medical devices that are constantly powered by electricity. If the ambulance is parked for a long time, it should be connected to electricity. Connect oly to a suitable grounded outlet!

2 power cords (orange - 5 m long; green - 2,5 m long) and one extension cord are included. The cables are stored under the passenger seat or behind the passenger seat.

Vehicle startup not possible – the ambulance is connected to the 230V external power supply network.

Central switch

If the car is stationary and it is not possible to power the car, please use the central switch. The central switch is used to disconnect the electricity in the rear of the car and to disconnect the light ramp. Never drive with the central switch off. The central switch is located under the driver's seat.

The door between the cab and the passengers area

The ambulance is equipped with the ignition shutdown system in compliance with PN EN 1789.9. The system blocks vehicle startup when the door between the driver compartment and the patient compartment if open. Then the vehicle starter is cut off. Closing the door results in the system deactivation and thus allows to startup the vehicle.

This security can be switched off using the 2 buttons behind the driver's seat.

1 - security active
0 - security inactive

Warning light and sound device

Sound warning

when the warning light is on only
using the horn button on the steering wheel
1 click - power on
1 click - switch sound
2 clicks - power off

Talking inside the cabin is heard outside through the speaker when this button is pressed.

Fuse panel

Control panel

Radio - switching on the speaker
Radio phone - switching on the speaker
Night light mode
Voltage converter (switching on 230 V sockets)
Heating power
Air conditioning power supply
Independent heating
Interior lighting
Interior lighting

10. Ventilation (inlet/outlet)

11. Infusion heating on.

12. Mode switching (none/heating when connected to 230 V/heating/cooling).

13. Temperature setting.

Seat shift

Extendable step

Transport technology

Mechanical stretcher support

Device: MEC 300
Manufacturer: STEM (Italy)

LOADING OF THE STRETCHER
The operation is conducted exclusively from the foot side of the support. Release the sliding tray by pulling lever. Slide the tray out while supporting it, it will then automatically lock into position when it reaches the end. During this operation the support will automatically tilt.

UNLOADING OF THE STRETCHER
Pull lever shown and slide the tray back in by pushing it inside the vehicle. Hold the tray all the way back until it locks automatically. After loading the stretcher adjust the inclination of the tray by activating the red lever.

IF DURING THE SLIDING OUT OF THE TRAY THE SUPPORT DOES NOT AUTOMATICALLY TILT, THEN:
The operation is conducted exclusively from the foot side of the support. Release the sliding tray by pulling lever. Slide the tray out while supporting it, it will then automatically lock into position when it reaches the end. During this operation the support will automatically tilt.

ADJUSTING THE INCLINATION THE STRETCHER

Stretcher cross slide
Press the black pedal and pull the stretcher to move it.

Stretcher

Device: Clinic Extero
Manufacturer: Medirol (Czech)
UA distributor: KSENKO; 1/11 Florencii str., of. 197; 02002 Kyjev; Phone +38 044 541 08 00 E-mail: office@ksenko.com; service +38 066 126 02 42

Chair with a stair system

Device: ROLMAN K312
Manufacturer: Medirol (Czech)
UA distributor: KSENKO; 1/11 Florencii str., of. 197; 02002 Kyjev; Phone +38 044 541 08 00 E-mail: office@ksenko.com; service +38 066 126 02 42

Baby and child restraint system

Device:Baby- und Kinderrückhaltesystem
Type: 720
Manufacturer: SCHNITZLER (Germany)

Medical DeviceS

Defibrilator

Device: DEFIGARD Tauch 7
Manufacturer: Schiller (Switzerland)
UA distributor: SCHILLER; 4-A, Zoologishna Str., office 139; Kyiv 03134; e-mail: office@schiller.com.ua

Suction Unit

Device: Laerdal Suction Unit
Manufacturer: Laerdal (Norway)
UA distributor: KSENKO; 1/11 Florencii str., of. 197; 02002 Kyjev; Phone +38 044 541 08 00 E-mail: office@ksenko.com; service +38 066 126 02 42